GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 236

background image

Configuration

75

2062973-003

3.

In the

Time Configuration

window, in

Configure Date and Time

, update the following

fields as needed:
•

Date

•

Month

•

Year

•

Hour:Minute

•

AM/PM

•

12/24 Hrs

4.

In the

Time Configuration

window, in

Configure Time Zone

, select the appropriate

UTC

Offset

, if applicable.

NOTE: The time zone configuration only applies to communication with Citrix server.

5.

Select

Save

.

The manual time configuration takes effect immediately.

7.4 Setting unit and bed name

Configure the care unit name and bed name for patient monitors that are configured to
connect to the MC Network.
NOTE: The unit name shall be set the same with all the patient monitors and CARESCAPE CIC
Pro central stations that are connected to the same care unit in the MC Network. Bed name
shall be unique to each patient monitor in the same care unit.
NOTE: Unit and bed name selections are not available if network selection is S/5.
1.

Log in to Webmin.

2.

Select

Configuration

>

Unit and Bed Name

.

3.

In the

Unit and Bed Name Configuration

window, view or set the unit name and bed

name for the device.

NOTE: Use only capital letters A - Z, numbers, dash (-), asterisk (*) and space ( ). The unit name
may be up to seven characters long and bed name up to five characters long.
4.

Select

Save

.

The unit and bed name configuration takes effect immediately.

7.5 Configuring printers

You can configure the patient monitor to print to up to 12 laser printers connected on the IX
Network. Use the Webmin sub-modules to install or delete a printer and to print a test page.
NOTE: Ensure that you have the host name(s) or IP address(es) for all the connected IX printers
available. Configure the IX printers according to this information.
NOTE: Laser printers that are installed on central stations do not need to be configured using
Webmin. Refer to the user’s manual for details on configuring the printer.
NOTE: Refer to the CARESCAPE Modular Monitors Supplemental Information Manual for the list
of supported devices.

7.5.1 Installing a printer

1.

Log in to Webmin.

2.

Select

Configuration

>

Printers

.

«
...
81
82
83
84
85
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Fisher Scientific Страницы: 42

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Konica Minolta Страницы: 32

Бренд: laerdal Страницы: 9

Бренд: Qlight Страницы: 4

Бренд: Abus Страницы: 8

Novation Launchkey Mini

Бренд: Focusrite Audio Engineering Страницы: 36

Бренд: Vitax Страницы: 12

Бренд: RAB Страницы: 4

Avisa Line XL04

Бренд: FHF Страницы: 2

Бренд: Joerns Healthcare Страницы: 106

CardioCare EKG2000

Бренд: Bionet Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды