GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 236

background image

CARESCAPE Monitor B450

114

2062973-003

NOTE: Make sure that at least one other patient monitor is on the network. The other patient
monitor must be in an admitted state and have an active ECG measurement with a simulator
signal.

Checkout procedure for wireless patient monitors

Check each wireless patient monitor according to the following procedure.
The purpose of this test is to ensure that each wireless patient monitor is correctly configured
1.

Disconnect the network cable from the MC Network connector, if connected.

2.

Check that the wireless network symbol and the signal strength symbol are shown

and that the signal strength is adequate.

3.

Select

Data & Pages – Other Patients

and select a patient from the list.

4.

Select

View

and verify that a window with parameters from another patient displays on

the left side of the screen. Check that the waveforms are continuous and there is no data
loss.

5.

Select

Close View

to close the window.

6.

Log in to Webmin.

7.

Select

Diagnostics > Ping

.

8.

Type the IP address of the patient monitor you just viewed and select

ping

. Check that the

patient monitor replies to the ping command, there are no lost packets and the maximum
latency is 250 ms.
NOTE: The patient monitor withstands a maximum packet loss of 5 packets per 1 million
and maximum latency of 250 ms without performance degradation.

9.

Select

to return to the main display.

10. Reconnect the MC Network cable back to the MC Network connector, if applicable.

Verification procedure for wireless MC Network infrastructure

Verify the wireless MC Network infrastructure according to the procedure described in
Appendix C.
The purpose of this test is to ensure the operation of the wireless network infrastructure
coverage area with a wireless CARESCAPE monitor.

8.3.11 IX printers

Perform the following test only if the patient monitor is connected to a printer in the IX Network
and you did not print a test page while you configured the IX printer.
1.

Log in to Webmin.

2.

Select

Configuration

>

Printers > Print Test Page

.

3.

Select the IX Printer to test.

4.

Select

Save

.

5.

Verify that the test page was printed to the selected printer.

6.

Repeat steps 3 to 5 for all connected IX printers.

«
...
120
121
122
123
124
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: Omlet Страницы: 60

Бренд: ABB Страницы: 33

Бренд: K-SPORT Страницы: 5

Бренд: Costan Страницы: 154

Chlorinsitu-III

Бренд: ProMinent Страницы: 120

DuraTech 45' 3-Way Retrieval SRL-R

Бренд: Falltech Страницы: 18

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды