GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 236

background image

Installation checkout

109

2062973-003

−

Polarity: REVERSED

−

Neutral: CLOSED

−

Earth (GND): OPEN

9.

Read and record the current leakage indicated on the safety tester.

10. Configure the safety analyzer as follows (SFC):

−

Polarity: REVERSED

−

Neutral: OPEN

−

Earth (GND): CLOSED

11. Read and record the current leakage indicated on the safety tester.
12. Configure the safety analyzer as follows (NC):

−

Polarity: REVERSED

−

Neutral: CLOSED

−

Earth (GND): CLOSED

13. Read and record the current leakage indicated on the safety tester.
14. Power off the device under test.
15. Repeat this test for all the connected parameter modules and patient connectors

Acceptance criteria in Normal Condition (NC):
•

All readings shall be less than or equal to 10

μ

A.

Acceptance criteria in Single Fault Condition (SFC) – earth open or one of the supply conductors
open at a time:
•

All readings shall be less than or equal to 50

μ

A.

8.2.9 Patient (sink) leakage current tests

This procedure measures the leakage current from an applied part connector of the device to
ground. Perform the test in Normal Condition (NC) with normal and reverse polarity.

NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

«
...
115
116
117
118
119
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

MicroVersaTrip Plus

Бренд: GE Страницы: 20

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: Obdstar Страницы: 10

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: Garelick Страницы: 4

Бренд: h/p/cosmos Страницы: 81

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

DISHSTAR ADA-SEER

Бренд: Jackson Страницы: 2

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды