GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 236

background image

Troubleshooting

141

2062973-003

11.2.2 Device information

The Device Information module shows the hardware and software information of the patient
monitor and the connected peripheral devices.
To view Device information:
1.

Log in to the Webmin.

Default Clinical Settings

•

Current default clinical settings.

Admit Settings

•

Patient ID Prefix.

Citrix

• Server address, initial program, session timeout in

minutes, username and encryption level.

Unit and Bed Name

•

Unit name and Bed name for CARESCAPE Network.

E-Module Information

•

STP/TP/ST configuration information and P/PT/PP
configuration information from E- modules.

S/5 Printers

•

Printer name.

IX Printers

•

Printer name, hostname or IP address.

Printer Location Information

•

Printout type (Alarm Waveforms, Numeric Trends,
Reports, and Waveforms) and Printer location.

Remote Service

•

Proxy URL, Proxy port, Proxy username, Remote service
status, System ID, Serial number, Enterprises URL,
Enterprises tunnel URL, and Protocol.

Language

•

Clinical user interface language.

National Requirement

•

Setting for country specific alarms (None or France).

Network

•

Active configuration information, including MAC address,
MC Network type (IP address, Netmask, Gateway,
Destination IP address, Destination netmask, and PHY
configuration), and IX Network type (IP address, Netmask,
Gateway, DNS server 1, DNS server 2, and PHY
configuration).

Power Line Frequency

•

Current power line frequency setting in use.

MUSE/12SL

•

Location ID, Site number, MUSE web username, and
MUSE web URL.

WLAN

•

Wireless LAN configuration information, including WLAN
radio status, Antenna Diversity, Region, Frequency Band,
RTS Threshold, Fragmentation Threshold, Applied QoS
Standard, WMM AC Parameters (for Voice, Video, Best
Effort, and Background), DSCP Settings (for Realtime
Clinical Traffic, Non-Realtime Clinical Traffic, and Non-
Realtime Non-Clinical Traffic), SSID, Authentication
method, Confidentiality method, and Key Index.

Configuration information

«
...
147
148
149
150
151
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Qingdao H.Y Страницы: 6

Бренд: Kapriol Страницы: 32

Ettan IPGphor 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 56

Бренд: GE Страницы: 132

Бренд: GE Страницы: 16

Бренд: GE Страницы: 474

Бренд: Facnor Страницы: 33

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: M-Audio Страницы: 3

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Raytec Страницы: 60

Бренд: Teac Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды