manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 173

 Troubleshooting

  165

2062973-003

E-module issues

PSM module issues

Possible cause

Recommended action

Incompatible module

Refer to the patient monitor’s supplemental information manual document 
to see the list of compatible modules.

DC/DC board failure

The +15 V MOD supply voltage for the E-module board is generated in the 
DC/DC board. Check from Webmin Hardware Statistics that the supply 
voltage is within specification
If the +15 V MOD is out of spec, the problem is most likely in the DC/DC 
board. Replace the DC/DC board.

CPU assembly failure

The RS-485 communication for the E-modules is managed by the EMBC 
section of the CPU carrier board.
- Check EMBC Frame logs for possible EMBC failures. 
If the cause is none of the above, the problem is most likely in the CPU 
carrier board. Replace the CPU assembly.

Possible cause

Recommended action

Pole mount cable loose or faulty (if 
the PSM module is mounted to a 
pole mount)

Check that the Module Bus Adapter for PSM and the connection cable is 
intact and properly connected to the PSM module mounted to the IV pole 
and to the PSM connector in the patient monitor.

DC/DC board failure

The +15VMOD supply voltage for the PSM module is generated in the DC/
DC board. Check that it is within specs, see section 

“11.3.1”

 for:

- +15VMOD voltage (mV)
If +15VMOD voltage is out of spec, the problem is most likely in the DC/DC 
board. Replace the DC/DC board.

CPU assembly failure

The RS-485 communication for the E-modules is managed by the EMBC 
section of the CPU carrier board.
- Check EMBC Frame logs for possible EMBC failures, see section 

“11.3.4”

. 

If the cause is none of the above, the problem is most likely in the CPU 
carrier board. Replace the CPU assembly.

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды