GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 236

background image

Using Webmin service interface

45

2062973-003

Webmin module

Use the module

Admit Settings

to configure Patient ID Prefix and barcode settings.

Citrix

to configure the Citrix client settings for the iPanel
software: server address, initial program, Citrix session
timeout, username, password, encryption level

Host Asset Settings

to enter a host asset number and to view the host serial
number.

Language

to select the language used in clinical user interface and
to select the keyboard locale setting for the
alphanumeric keyboard and the barcode reader.

Licenses

to enable and activate a software package, to enable
and activate software features and to upload and
activate a license file.

MUSE/12SL

to configure the host for sending and viewing 12SL
information.

Modules

to configure some acquisition module specific settings
after corrective maintenance, or for administrative
purposes. These settings are saved to the permanent
memory of the related acquisition module and the
settings travel with the module from one patient monitor
to another.
Refer to the Module Frames and Modules Technical
Manual for detailed information how to change these
settings.

National Requirements

to activate France specific defaults for the ECG HR
adjustment range and the reminder beep behavior.

Network

to select and configure the real-time network as the MC
Network (CARESCAPE Network) or S/5 Network. It also
allows the user to configure the IX Network settings.

Passwords

to change the passwords for the biomed and clinical
users.

Power frequency

to set the power line frequency.

Printers

to configure the patient monitor to print to up to 12 laser
printers connected on the IX Network. There are
sub-modules for installing a printer, deleting a printer
and for printing a test page.

Remote Service

to configure and control the Insite with Exc remote
service tool.

Restart

to shutdown and restart the patient monitor
automatically via Webmin.

NOTE: The patient must be discharged in order to enable
monitor restart via Webmin.

«
...
51
52
53
54
55
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Federal Страницы: 43

Бренд: Nitecore Страницы: 4

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Tar River Страницы: 26

Бренд: ZOLL Страницы: 38

Бренд: ZOLL Страницы: 36

Nature2 Fusion soft

Бренд: Zodiac Pool Systems Страницы: 52

Бренд: Oliver Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды