GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 63

Страница: 63 / 236

Hardware installation

2062973-003

Hardware installation

CAUTION

LOSS OF MONITORING - Leave space for circulation of air to prevent the
monitor from overheating. The manufacturer is not responsible for damage to

equipment caused by improperly vented cabinets, improper or faulty power, or

insufficient wall strength to support equipment mounted on such walls.

WARNING

The parameter modules are not able to withstand unpacked drops from a
height of 1 m without damage. If a module is dropped, please service it

before taking it back into use.

WARNING

After transferring or reinstalling the monitor, always check that it is

properly connected and all parts are securely attached.

WARNING

SITE REQUIREMENTS - Do not route cables or tubing in a way that they may
present a stumbling hazard.

WARNING

EXPLOSION - Do not use this equipment in the presence of flammable

anesthetics, vapors or liquids.

WARNING

EXCESSIVE TOUCH CURRENT - To avoid excessive patient leakage current,

do not simultaneously touch the patient and the electrical connectors
located at the rear panel of the monitor or within the module housing or

frames.

6.1 Installing a battery into the patient monitor and the

PDM module

The batteries for the patient monitor and the PDM module, if included, are shipped separately
and need to be installed and fully charged prior to taking into use.

WARNING

PHYSICAL INJURY- Make sure the battery is completely inserted and the
battery door is completely closed. Falling batteries could seriously or fatally

injure neonatal or other vulnerable patients.

WARNING

EXPLOSION OR FIRE -Using non-recommended batteries could result in

injury/burns to the patients or users. Only use batteries recommended or
manufactured by GE.

WARNING

EXPLOSION HAZARD - Do not incinerate a battery or store at high

temperatures. Serious injury or death could result.

NOTE: Refer to section

10.4. Monitor battery maintenance

in this manual for maintenance

instructions of the patient monitor battery. Refer to the Module Frames and Modules Technical
Manual for information about PDM battery maintenance.

6.1.1 Testing the battery charge

Before installing a battery, verify the battery’s state of charge. Press the green

TEST

button on

the battery. The number of charge level indicator LEDs that illuminate indicates the
approximate charge remaining in the battery.

−

Four LEDs illuminated: 75% – 100% of full-charge capacity.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды