GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 236

GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 76

CARESCAPE Monitor B450

68

2062973-003

3.

Enter the new hostname in the

Change Value to

column.

NOTE: The hostname is a unique, 4 to 32 character long identifier of a patient monitor in
the network. Use alphanumeric characters A-Z, a-z, 0-9. The hostname may include also
characters “-” and “_”, but it can't start or end with these characters.

4.

Select

Save

.

The hostname configuration will take effect immediately.

7.2.2 Selecting and configuring CARESCAPE Network

To select CARESCAPE Network MC for the real-time network infrastructure:
1.

Log in to Webmin.

2.

Select

Configuration >

Network > Wired Interfaces

.

The current network configuration is shown in the

Present Configuration

table.

3.

Below

Select Network Type

in the

Network Configuration

window, select the applicable

network type:

CARESCAPE Network

.

4.

Select

Next

to proceed on network configuration.

NOTE: When

CARESCAPE Network

is selected, the S/5 Network is disabled.

The patient monitor may be configured to the MC Network, or IX Network, or both.

NOTE: The following IP addresses are reserved and not valid: 172.16.254.254, 172.16.255.255,
172.18.254.254, 172.18.255.255, 192.168.250.x, 192.168.252.x, 192.168.253.x, 192.168.254.1
and 192.168.254.2.

5.

In the

Network Configuration

window below

MC Network.

a.

Enter a

Static IP

address.

b.

Enter a valid

Netmask

level.

c.

Select the applicable

Speed & Duplex

option.

6.

If separate MC Network segments are connected together by a router, configure the
router information below the MC static route:
a.

Enter

Destination Address

.

b.

Enter

Destination Netmask

.

c.

Enter an

MC Gateway.

7.

Below

IX Network,

select

DHCP

or

Manual Configuration

.

If

Manual Configuration

is selected, enter the following information in the entry fields:

a.

Enter a

Static IP

address.

b.

Enter a valid

Netmask

level.

c.

Enter a valid

Default Gateway

.

d.

Enter valid

DNS Server

addresses if applicable.

8.

Select the applicable

Speed & Duplex

option.

9.

Select

Save

.

Network connection(s)

Steps to be performed

MC Network only

5, (6) and 9

IX Network only

7, 8 and 9

Both MC and IX Network

5, (6), 7, 8 and 9

«
...
74
75
76
77
78
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды