GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 140

Страница: 140 / 236

CARESCAPE Monitor B450

132

2062973-003

10.3.10

Wireless LAN

Follow the procedure in section

8.3.10. Wireless LAN

10.3.11 IX printers

Follow the procedure in section

8.3.11. IX printers

10.3.12iPanel connection

Follow the procedure in section

8.3.12. iPanel connection

10.3.13 Insite with Exc

Follow the procedure in section

8.3.13. Insite with EXC

10.3.14 Recorder

Select

Monitor Setup > Printing > Devices > Setup

and configure:

Printout:

Waveforms

Location:

Local

Select

Monitor Setup > Printing > Waveforms

and configure:

Waveform 1:

Waveform 2:

Select

Monitor Setup > Printing > Waveforms > Print Waveforms

or the related soft key

in the main menu, or the

Print Waveforms

hard key in the keypad to start printing.

Verify that the recorder starts printing. Let the recorder print for approximately 10
seconds and verify the following things from the printout:

−

The header line contains the date, time and some other applicable status and
configuration information.

−

The grid is clear.

−

The waveforms labels appear in the printout as configured.

Stop printing by selecting

Monitor Setup > Printing > Waveforms > Stop Printing

, or the

related soft key in the main menu.

10.3.15 Synchronization connector test

Perform this test only if an E-PSM(P)(W) module is in use with the patient monitor.
NOTE: This test can't be performed with a PDM module. If the patient monitor is only used with
a PDM module, the synchronization connector test is not applicable.

Required Tools

−

E-PSM(P)(W) module

−

A multiparameter patient simulator with invasive pressure adapter cable to GE invasive
pressure connector.

−

5 lead ECG trunk cable, IEC or AHA

−

5 leadwire set, IEC or AHA

−

Oscilloscope

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды