GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 236

background image

Installation checkout

101

2062973-003

8

Installation checkout

The purpose of the installation checkout procedure is to ensure that the system is properly
installed and configured for use.
Service personnel shall perform the following checkout procedure for the monitoring system
after the hardware installation and platform configuration is completed:
•

8.1. Visual inspection

•

8.2. Electrical safety tests

NOTE: The manufacturer has performed the electrical safety test for the patient monitor
and acquisition modules during final inspection. You do not have to perform the electrical
safety tests during installation checkout, if there is less than 12 months since the patient
monitor was manufactured. Check the date of manufacture of the device from the device
label (see section

3.4.2. Equipment identification

).

•

8.3. Functional check

NOTE: Refer to chapter

10. Maintenance and checkout

to see the recommended checkout

procedure after corrective and planned maintenance.

8.1 Visual inspection

Perform the following visual inspection to the installed monitoring system:
•

Carefully inspect the patient monitor and the connected peripheral devices for any
damage.

•

Verify that the patient monitor and the connected peripheral devices are properly
mounted with specified mounting solutions.

•

Verify that the cables between the patient monitor and the connected peripheral devices
are intact, properly connected and secured to the right connectors.

•

Verify that the modules are properly connected and locked.

The cleaning precautions, requirements, procedures, and recommended cleaning solutions for
the patient monitor are described in the patient monitor’s user’s manual. For details about
cleaning, disinfecting and sterilizing the accessories, see the instructions for use in the
accessory package.

8.2 Electrical safety tests

Electrical safety tests provide a method of determining if potential electrical health hazards to
the patient or operator of the device exist.

8.2.1 Test setup

Test conditions

Perform electrical safety tests under normal ambient conditions of temperature, humidity and
pressure.

Test equipment

The test equipment required to perform electrical safety tests is listed below.

«
...
107
108
109
110
111
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Harken Страницы: 4

Бренд: Facsimile Страницы: 16

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Sonopuls HD 4050

Бренд: BANDELIN Страницы: 48

Бренд: JB-Lighting Страницы: 40

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: Ocean Sonics Страницы: 45

Бренд: neofeu Страницы: 28

Бренд: K-SPORT Страницы: 5

Бренд: Daekyung Страницы: 15

Бренд: Ivoclar Vivadent Страницы: 64

Бренд: Blizzard Lighting Страницы: 24

Бренд: Sima Страницы: 22

Бренд: J.P. SELECTA Страницы: 40

Бренд: Vibrapower HIIT Страницы: 24

ORTHODONTIC CHAIR

Бренд: DCI Edge Страницы: 16

Бренд: Malibu Boats Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды