Главная
/
GE HEALTHCARE
/
CARESCAPE Monitor B450
/
Техническое руководство

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться

Страница: 137 / 236

GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 137

Maintenance and checkout

129

2062973-003

10 Maintenance and checkout

This chapter specifies the checkout procedure and the maintenance activities to be performed
to the patient monitor after corrective maintenance and during annual planned maintenance.
This chapter also covers the battery maintenance information for the patient monitor’s lithium-
ion battery.

WARNING

Only perform maintenance procedures specifically described in the manual.

WARNING

Planned maintenance should be carried out annually. Failure to implement

the recommended maintenance schedule may cause equipment failure and
possible health hazards.

NOTE: The manufacturer does not, in any manner, assume the responsibility for performing the
recommended maintenance schedule, unless an Equipment Maintenance Agreement exists.
The sole responsibility rests with the individuals, hospitals, or institutions utilizing the device.
NOTE: Refer to Module Frames and Modules Technical Manual for corrective and planned
maintenance checkout procedures of the parameter modules.
NOTE: Refer to the PDM section in the Module Frames and Modules Technical Manual for the
battery maintenance procedure of the PDM battery.

Corrective maintenance

Service personnel shall perform the following checkout procedure steps after any corrective
maintenance, before taking the monitor back into clinical use:

«
...
135
136
137
138
139
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды