GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 236

background image

CARESCAPE Monitor B450

174

2062973-003

more than three times. Use only new screws attaching into light metal parts. Take
advantage of existing thread pattern cut by turning the screw counterclockwise until it
drops into the existing thread pattern.

•

We have added the maximum recommended torque value to be used for each screw and
nut in reassembly. These values are listed in brackets after each disassembly step.

•

When attaching self-tapping screws to light metal parts without existing threads (new
light metal FRU parts), you should use a higher torque than is recommended for
reassembled parts, but still not more than 1.6 Nm.

NOTE: It is not required to a use torque wrench or torque screwdriver when reattaching the
patient monitor using the recommended standard hand tools. Just ensure visually that the
screws are properly attached, but avoid over tightening by using excess force as this may
damage the existing thread patterns. However, when using battery-operated tools, ensure that
it is equipped with torque limiter and the torque is properly adjusted.

12.1.3

Required tools

NOTE: Use torque wrench and torque screwdriver to comply with the given torques.

WARNING

Due to possible high voltage present, use an insulated screwdriver at all
times.

12.1.4

Before disassembly

WARNING

PATIENT MONITORING INTERRUPTION — Make sure a patient is not being

monitored while servicing the equipment.

WARNING

DISCONNECTION FROM MAINS - When disconnecting the device from the
power line, remove the plug from the wall outlet first. Then you may

disconnect the power cord from the device. If you do not observe this

sequence, there is a risk of coming into contact with line voltage by
inserting metal objects, such as the pins of leadwires, into the sockets of the

power cord by mistake.

WARNING

SAFETY GROUND - Remove power cord from the mains source by grasping

the plug. Do not pull on the cable.

- insulated Torx T6 and T10 screwdrivers
- insulated flat blade screwdriver (width 2.5 mm

/ 0.1 in)

- pliers
- antistatic ESD wristband

«
...
180
181
182
183
184
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Labnet Страницы: 2

Бренд: idiag Страницы: 12

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: ABB Страницы: 4

Бренд: Tadano Страницы: 16

Бренд: FoodMarble Страницы: 44

Бренд: ISA Страницы: 24

Бренд: Torque Страницы: 10

SimNewB Anomaly Set

Бренд: laerdal Страницы: 10

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

Бренд: Marcy Страницы: 27

Бренд: Rocker Страницы: 23

Бренд: Western Global Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды