GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 236

GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 107

Configuration

99

2062973-003

activation is completed and the parameter module has restarted. This may take up to 15
minutes. Do not shut down the patient monitor or disconnect the parameter modules.
The parameter module restarts automatically after the software activation is complete.

4.

After the parameter module restarts, verify that the software activation is successful and
the parameter module runs the activated software.

7.19.3 Canceling pending host software activation

You can cancel a pending host software activation at any time while the message

Software

activation after next discharge/after next case end

is shown on the display.

1.

Log in to Webmin.

2.

Select

Configuration

>

Software Management.

The

Software Management

window opens.

3.

Select

Host Software

from the

Software List

and select

Next

.

4.

In the

Host Software

window, below

Status

, verify that the

Software activation pending

is

Yes

.

5.

Select

Cancel

.

The pending software activation is cancelled and the patient monitor continues running the
current software version.

7.19.4 Erasing an inactive software version.

You can erase an inactive host software version from the patient monitor. Erasing can prevent
the activation of a wrong software version by mistake.
1.

Log in to Webmin.

2.

Select

Configuration

>

Software Management

.

The

Software Management

window opens.

3.

Select the software that you want to erase and select

Next

.

The selected software activation window appears.

4.

Select

Erase

to erase the inactive software.

«
...
105
106
107
108
109
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды