Error solving manual.
CNC 8060
CNC 8065
·77·
(R
EF
: 1709)
1682
'Only one part number may be programmed'
DETECTION
During execution.
CAUSE
More than one part number have been programmed in the #DGWZ instruction.
SOLUTION
Program a single part number P1-P4.
1683
'The #REPOS instruction is only allowed in interruption subroutines'
DETECTION
During execution.
CAUSE
The #REPOS instruction is not programmed in an interruption subroutine.
SOLUTION
The #REPOS instruction can only be programmed in interruption subroutines.
Remove that instruction from any other subroutine or program.
1684
'Local subroutine and M, T, or G with subroutine in the same block'
DETECTION
During execution.
CAUSE
The same program block is executing a call to a local subroutine and an M, T or G
function that have an associated subroutine.
SOLUTION
Program the call to the local subroutine in another program block.
1685
'$GOTO: Jump to blocks nested inside a $IF, $FOR, $WHILE, etc. instruction not allowed'
DETECTION
During execution.
CAUSE
The instruction $GOTO is not inside a loop, but it is jumping to a label defined inside
an $IF, $FOR, etc. loop.
SOLUTION
Check the program. There could be no jumps into a loop.
1687
'Program: #REPOS <INT/INI> <sequence of axes/spindles>'
DETECTION
During execution.
CAUSE
The #REPOS instruction has been programmed wrong.
SOLUTION
The #REPOS instruction can include an optional parameter INT or INI, followed by
a sequence of axes and/or spindles fo the channel without a particular order.
1688
'No #REPOS instructions of any other type are allowed'
DETECTION
During execution.
CAUSE
There are different types (INT/INI) of #REPOS instructions programmed in the same
interruption subroutines.
SOLUTION
All #REPOS instructions must be of the same type.
1689
'No blocks are allowed after #REPOS'
DETECTION
During execution.
CAUSE
A block has been programmed between the #REPOS instructions and the end-of-
subroutine block in an interruption subroutine.
SOLUTION
The #REPOS instruction must be the last blocks of the interruption subroutine, except
the end-of-subroutine block.
1690
'Multiple axis programmed twice'
DETECTION
During execution.
CAUSE
'There cannot be more than one axis of the same multi-axis group programmed in
the same block'
SOLUTION
Check the program. Only program the active axis of the multi-axis group.
1691
'Nested G subroutine'
DETECTION
During execution.
CAUSE
In a subroutine associated with a G function, it is not possible to program the G
function that is calling this subroutine.
SOLUTION
Check the program. Do not program the G function inside the subroutine. In the case
of the G74, the function may be programmed inside the subroutine as long as it is
followed by the axes to be homed.
1692
'Program #VOLCOMP ON/OFF [n]'
DETECTION
During execution.
CAUSE
The instruction and/or some of its parameters are programmed wrong.
SOLUTION
Check the program.
Содержание 8065
