Error solving manual.
CNC 8060
CNC 8065
·11·
(R
EF
: 1709)
0072
'Feedback alarm not activated'
DETECTION
During the validation of the machine parameters.
CAUSE
In some set of parameters of an analog axis or spindle, the feedback alarm is not
activated. This situation can only be allowed during setup; once setup is completed,
this watch must be enabled.
SOLUTION
Activate the feedback alarm in all the sets of the analog axes and spindles (parameter
FBACKAL).
0073
'Software travel limits not activated'
DETECTION
During the validation of the machine parameters.
CAUSE
The software travel limits of some axis are not activated. Both LIMIT+ and LIMIT-
parameters of the axis are set to 0.
SOLUTION
Set the software travel limits of all the axes (parameters LIMIT+ and LIMIT).
0074
'Tendency test not activated'
DETECTION
During the validation of the machine parameters.
CAUSE
The tendency test of some axis or spindle is not activated. This situation should only
be allowed during setup; once the setup is completed, the tendency test must be
activated.
SOLUTION
Activate the tendency test for the axes and spindles (parameter TENDENCY).
0075
'Wrong I/O configuration table'
DETECTION
During the validation of the machine parameters.
CAUSE
Parameters NDIMOD and NDOMOD must be the same as the number of inputs and
outputs detected by hardware.
SOLUTION
Correct parameters NDIMOD and NDOMOD.
0076
'The sum of axes or spindles per channel exceeds the total number of axes or spindles'
DETECTION
During the validation of the machine parameters.
CAUSE
The value of parameter CHNAXIS is higher than the value of parameter NAXIS or
the value of parameter CHNSPDL is higher than the value of NSPDL.
SOLUTION
Correct the machine parameters.
0077
'Axis or spindle assigned to more than one channel'
DETECTION
During the validation of the machine parameters.
CAUSE
There is an axis or spindle assigned to several channels.
SOLUTION
Correct machine parameters CHAXISNAME and CHSPDLNAME n all the channels.
An axis or spindle can only belong to a channel or to none of them.
0078
'The master and slave axes must belong to the same channel'
DETECTION
During the validation of the machine parameters.
CAUSE
Some gantry axis is formed by axes of different channels.
SOLUTION
Both axes of a gantry axis must belong to the same channel.
0079
'A slave gantry axis cannot be parked'
DETECTION
On CNC power-up or when validating the machine parameters.
CAUSE
The CNC has detected that the slave axis of a gantry pair is parked; the PARKED
signal of the slave axis is active.
SOLUTION
Unpark the axis or cancel the gantry axis.
0080
'To validate the axis, you must validate the GENERAL PARAMETERS table'
DETECTION
During the validation of the machine parameters.
CAUSE
The user has added an axis to the system (parameter NAXIS) and, without validating
the general parameters table, has tried to validate the parameter table of one of the
new axes.
SOLUTION
Validate the general parameter table before validating the parameters of the axis.
0081
'The in-position zone cannot be smaller than the resolution of the axis'
DETECTION
During the validation of the machine parameters.
CAUSE
'The in-position zone is smaller than the resolution of the axis.
SOLUTION
Increase the in-position zone of the axis (parameter INPOSW).
Содержание 8065
