Baxi Platinum BC iPlus Скачать руководство пользователя страница 97

Страница: 97 / 116

3. Choose the contact directions of the BL1 IN and BL2 IN multifunc

tion inputs by setting the AP098 and AP099 parameters.

Tab.66

Parameter

Description

AP098

Blocking input 1 contact direction configuration

0 = input active on Open contact

1 = input active on Closed contact

AP099

Blocking input 2 contact direction configuration

0 = input active on Open contact

1 = input active on Closed contact

4. Configure the temperature offsets for the voluntary overheating by

configuring the HP091 and HP092 parameters.

Tab.67

Parameter

Description

HP091

Offset temperature of heating setpoint when

photovoltaic function is activated

HP092

Offset temperature of DHW setpoint when

photovoltaic function is activated

10.5.12 Reducing the noise level of the outdoor unit

Silent mode is used to reduce the noise level on the outdoor unit during a

given time range, particularly at night. This mode gives temporary prece

dence to silent running rather than temperature control.

Important

Silent mode only operates if the silent running kit is connected

to the outdoor unit.

This package is not compatible with the AWHP 4.5 MR outdoor

unit.

Silent mode is managed by the following parameters which can be found

in the Installer menu, EHC–04, ADV:

Tab.68

Parameter

Description

HP058

Enabling Heat pump Silent mode

HP094

Start time of the low noise when option activated

HP095

Stop time of the low noise when option activated

10.5.13 Detecting an additional or replacement PCB

The automatic detection function is used if a control PCB has been re

moved, replaced or added.

1. Go to the Installer menu.

2. Access the Installer menu by entering the code 0012 by pressing the

and keys.

3. Confirm access by pressing the

key.

4. Select the EHC–04 main PCB by pressing the or key.
5. Confirm the selection by pressing the

key.

10 Settings

7685645 - v04 - 07032018

AWHP-2 iMPI

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды