Baxi Platinum BC iPlus Скачать руководство пользователя страница 106

Страница: 106 / 116

3. Remove the spring retaining ring.

4. Remove the filter.

5. Inspect and clean the filter. Replace it if necessary.

6. Remount the filter.

7. Tighten the connection.

8. Open the valve on the exchanger.

11.4.2 Replacing the battery in the control panel

If the indoor unit is switched off, the control panel battery takes over to

keep the correct time.
The battery must be replaced when the time is no longer saved.

1. Remove the front panel by pulling firmly upwards.

2. Tilt the control panel support forwards.

Important

Keep a good hold of the control panel bracket in order not to pull

out or disconnect the electrical connections in the control panel.

3. Remove the battery located in back plate of the control panel by

pushing it gently forwards.

4. Insert a new battery.

Important

Battery type:

CR2032, 3V

Do not use rechargeable batteries.

Do not discard used batteries in the dustbin. Take them to an

appropriate collection place.

5. Re-assemble everything.

Fig.123 Removing the retaining ring and the

filter

MW-L000333-1

Fig.124 Accessing the back of the control

panel

MW-3000547-01

Fig.125 Remove the battery

MW-5000165-1

11 Maintenance

106

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды