Baxi Platinum BC iPlus Скачать руководство пользователя страница 68

Страница: 68 / 116

3. Select the number corresponding to the installation type by pressing

the or key. Selecting the installation type enables automatic

configuration of the parameters required for the control panel to op

erate correctly (gradient, maximum circuit temperature, etc.). For a
configuration which differs from those proposed here, press the

key on the control panel and configure the parameters manually.

Installation type

No.

One direct heating circuit

One direct heating circuit and one domestic hot water

tank

One direct heating circuit and one underfloor heating

circuit with mixing valve

One direct heating circuit and one domestic hot water

tank and one underfloor heating circuit with mixing

valve

One direct underfloor heating circuit

One direct underfloor heating circuit and one domestic

hot water tank

4. Confirm the selection by pressing the

key.

5. Set the heating curve.

The main parameters are set.

6. Based on the additional options connected, carry out the required

settings.

8.5

Checking the minimum flow

Heating installations must be able to guarantee a minimum flow rate at all

times. If the flow rate is too low, the heat pump may shut itself down for its

own protection; the heating, cooling and domestic hot water functions are

then no longer guaranteed.

1. Check the minimum flow rate as defined by the HP010 parameter.

See

The flow rate value within the installation can be read using the

AM056 parameter.

2. Set the differential pressure valves to guarantee an optimum flow

rate in the installation when thermostatic valves are closed. The opti

mum flow rate is defined by the HP069 parameter.

8.6

Final instructions

The various parameters for the heat pump are pre-set in the factory.

These factory settings are suitable for the most common heating systems.

For other systems and situations, the parameters can be modified.

1. Deactivate the heat pump's domestic hot water mode.

2. Simulate a heat demand to start up heating mode.

3. Check start-up of the outdoor unit and the back-ups connected.

4. Check the flow rate in the installation in comparison to the minimum

flow rate.

5. Put the heat pump in shut-down/frost protection mode.

Fig.77

-1

Fig.78

MW-10001142-2

19°

8 Commissioning

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды