Baxi Platinum BC iPlus Скачать руководство пользователя страница 111

Страница: 111 / 116

Fault

code

Message

Description

E02.24

System flow locking active

System water flow locking active

No circulation:

Check that the circulation pump is

working.

Check that the valves and thermostatic

valves are open.

Check the wiring.

Check the pump supply: if the pump

does not work, replace it.

Too much air

Completely vent the indoor module

and the installation for optimum run

ning.

Check that the automatic air vents are

properly open (also check the hydro

block).

Completely vent the indoor module and

the installation for optimum running.

Incorrect wiring: check the electrical con

nections.

Flow meter:

Check the electrical connections and

the direction of the flow meter (arrow

to the right).

Replace the flow meter if necessary.

12.2.3 Alarm codes

An alarm code is a temporary heat pump status, resulting from the detec

tion of an anomaly. If an alarm code still remains after several automatic

start-up attempts, the system goes into fault mode.

Tab.75 List of alarm codes

Error code

Message

Description

A02.06

Water Press Warning

Water Pressure Warning active

A02.18

OBD Error

Object Dictionary Error

A02.22

System flow warning

System water flow warning active

A02.55

Inval or miss SerNR

Invalid or missing device serial number

12.3 Accessing the error memory

The error and fault codes are listed together in the memory.

1. Access the menus by pressing the two keys on the right simultane

ously.

Fig.129

MW-2000369-1

12 Troubleshooting

7685645 - v04 - 07032018

AWHP-2 iMPI

111

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды