Baxi Platinum BC iPlus Скачать руководство пользователя страница 74

Страница: 74 / 116

1. Go to stop mode by pressing the

key.

2. Select the heating mode by pressing the key.
3. Confirm by pressing the

key.

4. Select the heating shut-down pressing the key.

The screen displays: .

The frost protection function continues to run.

The heating and cooling have been shut down.

Important
Press the key to restart the appliance: the screen will
display .

5. Confirm by pressing the

key.

6. Go back to the main display by pressing the

key.

Important

The display disappears after a few seconds of inactivity.

9.3.2

Shutting down the cooling function

Important

If the heating function is shut off, then the cooling will also be shut

off.

1. Access the menu.
2. Confirm access by pressing the

key.

3. Select CIRCA or CIRCB by pressing the or key.
4. Confirm the selection by pressing the

key.

5. Select TP.C by pressing the or keys.
6. Confirm the selection by pressing the

key.

7. Modify the timer program to stop cooling.

9.4

Frost Protection

If the temperature of the heating water in the heat pump falls too much,

the integrated protection device switches itself on. This device functions as

follows:

If the water temperature is lower than 5°C, the circulating pump starts

up.

If the water temperature is lower than 3°C, the back-up starts up.

If the water temperature is higher than 10°C, the back-up shuts down

and the circulating pump continues to run for a short time.

Fig.99

MW-5000027-4

Fig.100

MW-5000133-3

Fig.101

MW-5000134-3

9 Operation

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды