Baxi Platinum BC iPlus Скачать руководство пользователя страница 108

Страница: 108 / 116

Error

code

Message

Description

H00.32

TOutside Open

Outside temperature sensor is either removed or measures a temperature below range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.33

TOutside Closed

Outside temperature sensor is either shorted or measures a temperature above range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.47

HP flow sens removed

or below range

Heat pump flow temperature sensor is either removed or measures a temperature

below range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.48

THp Flow Closed

Heat pump flow temperature sensor is either shorted or measures a temperature

above range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.51

THp Return Open

Heat pump return temperature sensor is either removed or measures a temperature

below range

H00.52

THp Return Closed

Heat pump return temperature sensor is either shorted or measures a temperature

above range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.57

T DHW Top Open

Domestic Hot Water top temperature sensor is either removed or measures a

temperature below range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H00.58

T DHW Top Closed

Domestic Hot Water top temperature sensor is either shorted or measures a

temperature above range

Check the wiring between the central unit PCB and the sensor.

Check that the sensor has been fitted properly.

Check the Ohmic value of the sensor.

Replace the sensor if necessary.

H02.00

Reset In Progress

H02.02

Wait Config Number

Waiting For Configuration Number

Waiting for configuration parameters to be entered

Configure CN1 / CN2 depending on the output of the outdoor unit installed (CNF

menu).

Central unit PCB replaced: heat pump not configured

H02.03

Conf Error

Configuration Error

The configuration parameters entered are incorrect.

Configure CN1 / CN2 depending on the output of the outdoor unit installed (CNF

menu).

12 Troubleshooting

108

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды