Baxi Platinum BC iPlus Скачать руководство пользователя страница 98

Страница: 98 / 116

6. Select the auto detection parameter by pressing the or keys.
7. Confirm auto detection by pressing the

key.

The automatic detection function is running.

10.6 Reading out measured values

The measured values are available in the Information menu of the dif

ferent PCBs.
Certain parameters are displayed:

according to certain system configurations,

according to the options, circuits or sensors actually connected.

Tab.69 Choosing the menu

Counters

Selection

Measured values on circuit A

Choose menu EHC-04

Measured values on circuit B

Choose menu SCB04-B

Measured values connected to the

operation of the heat pump

Choose menu EHC-04

Tab.70 Values available (X) in the sub-menus EHC-04, SCB04-B

Parameter

Description

Unit

EHC-04

SCB04-B

AM002

"Silent mode" status

AM010

The current pump speed

AM012

Current main status of the appliance.

See

Control system sequence chapter

AM014

Current sub status of the appliance.

See

Control system sequence chapter

AM015

Is the pump running?

AM016

Flow temperature of appliance.

°C

AM019

Water pressure of the primary circuit.

bar

AM027

Instantaneous outside temperature

°C

AM040

Temperature used for hot water control algorithms.

°C

AM056

Wate flow rate in the system

l/min

AM091

Seasonal mode active (summer / winter)

0: Winter

1: Frost protection

2: Summer neutral band

3: Summer

AM101

Internal system flow temperature setpoint

CM030

Measure of the Room temperature of the zone

°C

Fig.119

-1

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды