Baxi Platinum BC iPlus Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 116

background image

See

Boiler installation manual.

Configuring a boiler not equipped with a room thermostat input

1. Set the following installer parameters on the boiler control panel:

Switch the boiler control system to 24h/24 comfort mode.

Heating set point temperature = Domestic hot water set point tem

pe 5°C.

See

Boiler installation manual.

10.5.6 Configuring the hybrid operating mode of a hydraulic

back-up

Important

Hybrid operating mode is only available for appliances with a hy

draulic back-up.

The hybrid function consists of an automatic switch between the heat

pump and the boiler, according to the cost, the consumption or emission of

CO

2

of each heat generator.

Tab.61 Calculating the threshold coefficient of performance
If the coefficient of performance of the heat pump is higher than the threshold coefficient of performance, the heat pump takes

priority. Otherwise only the boiler back-up is enabled. The heat pump coefficient of performance depends on the outside tem

perature and the heating water set point temperature.

HP061 parame

ter

Description

HP061 = 1

Optimisation of energy costs for the consumer (factory setting): the control system chooses the cheapest

generator according to the coefficient of performance of the heat pump and according to energy cost.

The switch between the heat pump and the boiler occurs at the value of the threshold coefficient of per

formance calculated according to energy cost optimisation mode with the energy cost parameters.

HP062: Energy cost in Hybrid Electricity cost in high tarif
HP063: Energy cost in Hybrid Electricity cost in low tarif
HP064: Cost of fossil energy (oil or gas) – price per m

3

or per litre – Can be set from 0.01 to 2.50 €/kWh

HP061 = 2

Optimisation of primary energy consumption: The control system chooses the generator that consumes the

least primary energy.

The switch between the heat pump and the boiler occurs at the HP054 threshold coefficient of performance

value according to the primary energy consumption optimisation mode.

HP061 = 3

Optimisation of CO

2

emissions: The control system chooses the generator that emits the least CO

2

.

The switch between the heat pump and the boiler occurs at the threshold coefficient of performance value

calculated according to the CO

2

emissions optimisation mode:

HP065: Electrical CO2 emission in heating mode
HP066: Electrical CO2 emission in DHW mode
HP067: Gas or Oil CO2 emission

HP061 = 0

No optimisation: The heat pump always starts up first, regardless of the conditions. The boiler back-up

starts up afterwards, if required.

10 Settings

7685645 - v04 - 07032018

AWHP-2 iMPI

93

«
...
91
92
93
94
95
...
»

Содержание Platinum BC iPlus





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Platinum BC iPlus

Бренд: Marta Страницы: 12

Бренд: VEAB Страницы: 16

Бренд: Zibro Страницы: 16

Бренд: Zibro Страницы: 17

Бренд: MasterCraft Страницы: 8

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

Бренд: Webasto Страницы: 12

Бренд: Binks Страницы: 22

Бренд: Mr. Heater Страницы: 36

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

Optyma Slimpack OP-LSQM Series

Бренд: Danfoss Страницы: 174

ULTRA-FLO MY3-50 METAL Series

Бренд: Q-MAX Страницы: 12

Бренд: Wayne Страницы: 12

Бренд: Blue Angel Страницы: 4

Бренд: DEMA Страницы: 8

Бренд: NARVI Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды