Baxi Platinum BC iPlus Скачать руководство пользователя страница 89

Страница: 89 / 116

Live

Operating description

Heating only. When the DP120 differential is reached, domestic hot water production is triggered.

If there is not enough domestic hot water (e.g. if the domestic hot water does not heat up quickly

enough): reduce the trip differential (hysteresis) by modifying the value of the DP120 parameter. The

DHW tank will then heat up the water more quickly.

Domestic hot water production only.

10.4.3 Running the back-up in domestic hot water mode

Start-up conditions for the back-up

The start-up conditions for the back-up producing domestic hot water are

described in the following table.

Tab.53

Parameter

Setting

AP001

The function of the BL1 blocking input is not set to 4, 6 or 8

AP100

The function of the BL2 blocking input is not set to 4, 6 or 8

AP098

Blocking input 1 contact direction configuration

0 = input active on Open contact

1 = input active on Closed contact

2 = input active on Off contact

AP099

Blocking input 2 contact direction configuration

0 = input active on Open contact

1 = input active on Closed contact

Operating description

The behaviour of the hydraulic or electrical back-up in domestic hot water

mode depends on the configuration of the DP051 parameter.

Tab.54 Behaviour of the hydraulic or electrical back-up

Value of the DP051 parameter

Operating description

The system gives priority to the heat pump during domestic hot water production.

Recourse to the hydraulic or electrical back-up is only taken if the DP090 time delay has

elapsed in domestic hot water mode, unless hybrid mode is activated. In that case, hy

brid logic takes over.

Domestic hot water production mode gives priority to comfort by accelerating domestic

hot water production by simultaneously using the heat pump and the hydraulic or electri

cal back-up.

In this mode, there is no maximum time for domestic hot water production as the use of

the back-ups helps to ensure domestic hot water comfort more quickly.

10.5 Setting the parameters

10.5.1 Language selection

1. Access the User menu.

2. Select the HMI sub-menu.

10 Settings

7685645 - v04 - 07032018

AWHP-2 iMPI

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды