Baxi Platinum BC iPlus Скачать руководство пользователя страница 96

Страница: 96 / 116

10.5.9 Drying screed without the heat pump outdoor unit.

The indoor module can be used for drying screed using the electrical

back-up in forced operation mode. It is not necessary to connect the out

door unit.

1. Switch on the heat pump and activate the screed drying function.

2. Adjust the parameters for screed drying.

3. Force the electrical back-up by increasing the value of the HP000

parameter.

10.5.10 Supplying the heat pump with photovoltaic energy

When lower cost electrical energy is available, such as photovoltaic ener

gy, the heating circuit and domestic hot water tank (if present) can be

overheated. Underfloor cooling cannot be supplied with power in this way.
To activate this functionality, enter data for the AP001 parameter and con

nect a dry contact to the BL1 input or the AP100 parameter and a dry con

tact on the BL2 input.

Tab.64 Voluntary overheating parameters

Parameter

Description

AP001 or AP100

Hydraulic back-up: 8 (Photovoltaic with heat pump only)

Electrical back-up: 9 (Photovoltaic with electrical back-up)

HP091

Offset temperature of heating setpoint when photovoltaic function is activated

HP092

Offset temperature of DHW setpoint when photovoltaic function is activated

10.5.11 Connecting the installation to a Smart Grid

The heat pump can receive and manage control signals from the "smart"

energy distribution network (Smart Grid). Based on the signals received by

the terminals of the BL1 IN and BL2 IN multifunction inputs, the heat pump

shuts down or voluntarily overheats the heating system in order to opti

mise electricity consumption.

Tab.65 Operation of the heat pump in a Smart Grid

BL1 IN

input

BL2 IN in

put

Operating

Inactive Inactive

Normal: The heat pump and the electrical back-up

operate normally

Active

Inactive

Shutdown: The heat pump and the electrical back-

up are shut down

Inactive Active

Economy: The heat pump voluntarily overheats

the system without the electrical back-up

Active

Super Economy: The heat pump voluntarily over

heats the system with the electrical back-up

1. Connect the Smart Grid signal inputs to the BL1 IN and BL2 IN in

puts on the EHC–04 PCB. Smart Grid signals come from dry con

tacts.

Germany: Connect the SG1 and SG2 terminals respectively from the

electricity meter to the BL1 IN and BL2 IN inputs on the EHC–04

power circuit board.

2. Set the AP001 and AP100 parameters to 10.

The heat pump is ready to receive and manage Smart Grid sig

nals.

Fig.118

-1

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды