Baxi Platinum BC iPlus Скачать руководство пользователя страница 92

Страница: 92 / 116

Energy meter specifications

Minimum admissible voltage: 27 V
Minimum admissible intensity: 20 mA
Minimum pulse time: 25 ms
Maximum frequency: 20 Hz
Pulse weighting: between 1 and 1000 Wh

Choose meters whose impulse number per kW is a multiple of 1000.

Energy metering provides information on:

electrical energy consumption,

the production of thermal energy for heating, domestic hot water and

cooling modes.

The thermal energy from the hydraulic or electrical back-up is also fac

tored in to provide the full tally of restored thermal energy.

1. Go to the Installer menu.
2. Access the Installer menu: enter the code 0012 by pressing the

and keys.

3. Confirm access by pressing the

key.

4. Select EHC-04 by pressing the or key.
5. Confirm access by pressing the

key.

6. Configure the HP033, HP034 and HP035 parameters.

Tab.58

Situation

Configuration

According to the type of

energy meter installed

Adjust the impulse value of the HP033 parameter. The setting range of the HP033 parameter goes

from 0 (no metering) to 1000 Wh.

The default setting for the impulse weight is 1 Wh.

If the meter impulse weight is given in a number of impulses per kWh, divide this value by 1000.

If a hydraulic back-up is

fitted

Set the HP034 and HP035 parameters to 0.

If an electrical back-up

is fitted

Set the HP034 and HP035 parameters according to the configuration of the electrical back-up stages

output.

10.5.5 Configuring a hydraulic back-up

1. Configure the back-up boiler according to its control panel.

Configuring a boiler equipped with a room thermostat input

1. Set the following installer parameters on the boiler control panel.

Tab.59 Setting with MK2 control panel

Parameter

Setting

E.TEL

THERM A

TPC J / TPC N

Domestic hot water set point tempe5°C

PENTE CIRC.A

0.0

Tab.60 Setting with another control panel

Parameter

Setting

Heating / Boiler thermostat set point temperature

Domestic hot water set point tempe5°C

2. Switch off the control panel.

3. Disconnect the outside temperature sensor.

4. Mount a 1-kOhm resistor instead of the outside sensor.

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды