Baxi Platinum BC iPlus Скачать руководство пользователя страница 80

Страница: 80 / 116

Tab.42 List of ADV parameters in the sub-menu of the Installer menu

ADV

Description of the ADV advanced parameters

Factory setting

DP004

Legionella mode protection calorifier

0 =Disabled

1 = on: the domestic hot water tank is superheated to 65 °C for 20 minutes

once a week.

2 = automatic: the domestic hot water tank is remotely controlled.

DP046

Maximum domestic hot water temperature

Can be set from 10 °C to 70 °C

DP047

Maximum time allowed to produce Domestic Hot Water

Can be set from 1 to 10 hours

3 (4.5 kW - 6 kW - 8

kW)

2 (11 kW - 16 kW)

DP048

Minimum heating time before Domestic Hot Water production

Can be set from 0 to 10 hours

DP055

Enable/disable the TAS protection of the DHW tankCan be set from 0 to 1

DP090

Delay for starting the next generator (backup stage) in DHW mode

Can be set from 0 Min to 120 Min

DP100

Delay for stopping the next generator (backup stage) in DHW mode

Can be set from 0 Min to 120 Min

DP110

Delay for starting the next generator (backup stage) in DHW mode

Can be set from 0 Min to 255 Min

DP150

Enable DHW Thermostat function

0 =Off

1 =On

DP160

Setpoint for DHW anti legionella

Can be set from 60 °C to 90 °C

Do not modify this setting

10.2.5 Installer \EHC–04 and SCB-04 menu

AP : Appliance Parameters = Appliance parameters

Tab.43

Parameter

Description

Factory setting

EHC–04

Factory setting

SCB-04

AP001

Blocking input setting (1: Full blocking, 2: Partial blocking, 3: User

reset locking) BL1:

1 = Full blocking of the installation – frost protection not guaran

teed

2 = Partial blocking of the installation – frost protection active

3 =User reset locking

4 =Backup Relieved

5 =Heat Pump Relieved

6 =HP & backup relieved

7 =High, Low Tariff

8 =Photovoltaic HP Only

9 =PV HP And backup

10 =Smart Grid ready

11= heating/cooling

not available

AP028

Defines the type of cooling used.

0 =Off

1 =Active cooling on

2 = Free cooling on, not used

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды