Baxi Platinum BC iPlus Скачать руководство пользователя страница 84

Страница: 84 / 116

ADV parameter

Description of the ADV advanced parameters

Factory setting

EHC–04

HP047

Maximum time at maximum outside temperature to start back up in CH mode

when dynamic timer selected

Can be set from 1 to 10 minutes

Value accepted when HP031 = 0

HP048

Maximum time at maximum outside temperature to start back up in CH mode

when dynamic timer selected

Can be set from 0 to 60 minutes

Value accepted when HP031 = 0

HP049

Minimum outside temperature for dynamic timer when dynamic mode is selected

Can be set from -30 to 0 °C

Value accepted when HP031 = 0

-10

HP050

Maximum outside temperature for dynamic timer when dynamic mode is

selected

Can be set from -30 to +20 °C

Value accepted when HP031 = 0

HP051

Minimum operating temperature for the heat pump

Can be set from -20 to +5 °C

-15 °C for 4.5 kW

-15 °C for 6 kW

-20 °C for 8 kW

-20 °C for 11 kW

-20 °C for 16 kW

HP058

Enabling Heat pump Silent mode

0 =No

1 =Yes

Requires a specific option. Not available for AWHP 4.5 MR.

HP069

Heat Pump flow speed set-point depending on Heat Pump Power configuration

Can be set from 0 to 100 l/min

12 for 4.5 kW

17 for 6 kW

23 for 8 kW

32 for 11 kW

46 for 16 kW

HP079

Maximum offset applied on the dynamic cooling setpoint when a 0-10V humidity

sensor is used

Can be set from 0 to 15°C

HP086

Activation of hydraulic management mode for the configuration with a low-loss

header, or for a buffer tank connected as a low-loss header

0 =No

1 =Yes

HP087

Buffer tank hysteresis to start and stop heating

Can be set from 0 to 30 °C

HP091

Offset temperature of heating setpoint when photovoltaic function is activated

Can be set from 0 to 30 °C

HP092

Offset temperature of DHW setpoint when photovoltaic function is activated

Can be set from 0 to 30 °C

HP094

Start time of the low noise when option activated

Can be set from 00:00 to 23:59

Value accepted when HP058 = 1

22:00

HP095

Stop time of the low noise when option activated

Can be set from 00:00 to 23:59.

Value accepted when HP058 = 1

06:00

HP108

Activation time delays for the back-ups between stage 1 and stage 2 (electrical

back-up) in central heating mode

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды