Baxi Platinum BC iPlus Скачать руководство пользователя страница 102

Страница: 102 / 116

Status Appliance: AM012 parameter

Appliance sub status: AM014 parameter

Blocking Mode

30= normal operation.

The compressor or the back-ups are running.

31= internal set point limited

If the heating set point on the heat pump differs from the system set point.

60= pump post-operation

Heat pump and back-up shut-down, system pump running.

65= compressor bypass

The back-ups are operating.

66= the temperature exceeds the compressor's maximum operating tempera

ture

The compressor has stopped. The back-ups are operating.

67= the outside temperature is lower than the compressor's maximum operat

ing temperature

The compressor has stopped. The back-ups are operating.

68= the hybrid function requests compressor shut-down

The compressor has stopped. The back-ups are operating.

69= defrosting running

The compressor is running.

70= defrosting conditions not met

The compressor has stopped. The back-ups are operating.

71= defrosting running.

The compressor and the back-ups are running.

Locking Mode

Load test min

Load test CH max

30= normal operation. The compressor or the back-ups are running.

31= internal set point limited

If the heating set point on the heat pump differs from the system set point.

60= pump post-operation

Heat pump and back-up shut-down, system pump post-operation.

65= compressor bypass and back-ups running

66= the temperature exceeds the compressor's maximum operating tempera

ture

The compressor has stopped. The back-ups are operating.

67= the outside temperature is lower than the compressor's maximum operat

ing temperature

The compressor has stopped. The back-ups are operating.

68= the hybrid function requests compressor shut-down

The compressor has stopped. The back-ups are operating.

69= defrosting running

The compressor is running.

70= defrosting conditions not provided

The compressor has stopped. The back-ups are operating.

71= defrosting running.

The compressor and the back-ups are running.

10 Settings

102

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды