Baxi Platinum BC iPlus Скачать руководство пользователя страница 9

Страница: 9 / 116

After maintenance or repair work, check the entire heating system to en

sure that there are no leaks.
Remove the casing only to perform maintenance and repair work. Put the

casing back in place after maintenance and repair work.

1.9

Liabilities

Manufacturer's liability

Our products are manufactured in compliance with the requirements of the various Directives appli

cable. They are therefore delivered with the marking and any documents necessary. In the inter

ests of the quality of our products, we strive constantly to improve them. We therefore reserve the

right to modify the specifications given in this document.

Our liability as manufacturer may not be invoked in the following cases:

Failure to abide by the instructions on installing the appliance.

Failure to abide by the instructions on using the appliance.

Faulty or insufficient maintenance of the appliance.

Installer's liability

The installer is responsible for the installation and initial commissioning of the appliance. The instal

ler must observe the following instructions:

Read and follow the instructions given in the manuals provided with the appliance.

Install the appliance in compliance with prevailing legislation and standards.

Carry out initial commissioning and any checks necessary.

Explain the installation to the user.

If maintenance is necessary, warn the user of the obligation to check the appliance and keep it in

good working order.

Give all the instruction manuals to the user.

1 Safety instructions and recommendations

7685645 - v04 - 07032018

AWHP-2 iMPI

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды