Baxi Platinum BC iPlus Скачать руководство пользователя страница 94

Страница: 94 / 116

C COP: Coefficient of performance

Threshold coefficient of performance

T Outdoor temperature

HP051 parameter: Minimum outside temperature below which

Heat Pump is stopped

HP000 parameter: Outside bivalence temperature

10.5.7 Configuring a convection fan or underfloor cooling

This function is only available when the type of circuit selected is under

floor heating or convection fan: CP020 parameter set to 2 or 5.

Important

The heating should be activated in order for the cooling to func

tion.

1. Go to the Installer menu.

2. Access the Installer menu by entering the code 0012 by pressing the

and keys.

3. Confirm access by pressing the

key.

4. Access the EHC–04 PCB parameters by pressing the or key.

5. Select the AP028 parameter corresponding to cooling by pressing

the or keys.

6. Confirm by pressing the

key.

7. Select value 1 by pressing on the to activate the cooling function.

8. Confirm by pressing the

key.

9. Go back to the main display by pressing

10. Program the desired cooling hours in the menu, circuit A or B,

TP.C sub-menu.

11. Go back to the main display by pressing

12. If necessary, force cooling or configure cooling temperatures in the

User menu, circuits A and B:

Tab.62

Parameter

Description

AP015

Force manually the heat pump in cooling mode

AP016

Activating/deactivating heating: deactivating heating also deactivates cooling.

CP270

Mixing flow temperature setpoint cooling of the zone

CP280

Fan flow setpoint cooling of the zone

13. Check the setting for the CP690 parameters according to the ther

mostat or room sensor used.

Fig.113 Influence of outdoor temperatures

and bi-valency.

MW-5000542-1

Fig.114

-4

-2

Fig.115

MW-6000366-3

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды