Baxi Platinum BC iPlus Скачать руководство пользователя страница 86

Страница: 86 / 116

Parameter

Description

Unit

EHC-04

SCB04-B

AC027

Counter that shows the number of pump starts

AC028

Total working time of the first stage of backup

hours

AC029

Total working time of the second stage of backup hours

AC030

Total startings of the first stage of backup

AC031

Total startings of the second stage of backup

DC002

Numbers of Domestic Hot Water diverting valve

cycles

DC003

Number of hours during which the diverting valve

is in DHW position

hours

DC004

Number of compressor start-ups during domestic

hot water production

DC005

Number of compressor start-ups

PC002

Number of compressor start-ups

PC003

Number of compressor operating hours

hours

CODE

Enter the installer code to access the following pa

rameters.

AC002

Number of hours that the appliance has been

producing energy since last service

hours

AC003

Number of hours since the previous servicing of

the appliance

hours

AC004

Number of generator startings since the previous

servicing.

AC013

Seasonal coefficient of performance

SERVICE

Resetting the maintenance service

CLR: the AC002, AC003, and AC004 counters are

reset to zero.

10.3.2 COUNTERS, TIME PROG, CLOCK \CIRCA, CIRCB

and DHW menus

Tab.50

Description

CIRCA

TP.H: Timer programming for heating

06:00 - 23:00 ON

23:00 - 06:00 OFF

TP.C: Timer programming for cooling

14:00 - 23:00 ON

23:00 - 14:00 OFF

CIRCB

Timer programming for heating

06:00 - 23:00 ON

23:00 - 06:00 OFF

DHW

Timer programming for domestic hot water

06:00 - 23:00 ON

23:00 - 06:00 OFF

10 Settings

AWHP-2 iMPI

7685645 - v04 - 07032018

Содержание Platinum BC iPlus





















































































































Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды

Baxi Platinum BC iPlus, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Platinum BC iPlus

Отзывы:

Похожие инструкции для Platinum BC iPlus

Бренды по названию

Популярные бренды