Basler BE1-BPR Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 148

background image

BE1-BPR Functional Description

4-1

SECTION 4 • FUNCTIONAL DESCRIPTION

GENERAL

BE1-BPR Breaker Protection Relays are microprocessor-based devices that provide breaker failure pro-
tection, optional fault recording, and diagnostic monitoring of breaker wear and breaker resistor overheating.
This section describes the hardware and software functional descriptions.

HARDWARE FUNCTIONAL DESCRIPTION

BPRs are available as either 19 inch rack mount units or vertical panel mount units. The rack mount is
approximately 3.48 inches high and the vertical panel mount is about 5.38 inches wide and 14.32 inches
high. The vertical panel mount unit assemblies are arranged differently to fit the 14.32 inch casing. A trans-
parent front cover protects the unit but allows access to some front panel controls. A spring loaded handle
under the front cover retracts when released and provides drawout capability of the BPR relay (chassis
assembly) from the rack assembly. It is not necessary to disturb system wiring when removing a BPR relay
from the case.

The hardware function description is divided into three categories: inputs, circuit operation, and outputs.

Inputs

There are five types of inputs to the BPR relay. They are:

Operating Power

Contact Sensing

Current Sensing

Keyboard

Serial Ports RS-232/RS-485

Operating Power

Operating power for the internal circuitry is applied to the isolated internal switching power supply. Required
operating power is either 48/125 VDC or 125/250 VDC and is determined by the relay part number shown
in Section 1,

General Information, Specifications.

Contact Sensing

Seven external contact sensing inputs provide external stimulus to initiate BPR relay actions. Nominal volt-
age(s) of the external dc source(s) must fall within the relay DC power supply input voltage range. If the
power supply of the relay has an ac source, a separate dc source must be used for the contact sensing input
voltage. Three contact sensing inputs (IN1 through IN3) are individually isolated. IN4 and IN5 are isolated
from other circuits but share a common return. IN6 and IN7 are also isolated from other circuits but share
a common return.

Current Sensing

Monitored line and neutral currents are applied to internal current transformer primaries and stepped down
to internal circuit levels. The internal current transformers provide isolation from the monitored line currents.

Keyboard

A five key keyboard (illustrated in Section 3) provides limited local programming capability and the ability
to select a number of status and diagnostic menu screens.

«
...
42
43
44
45
46
...
»

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

Бренд: schmersal Страницы: 6

Бренд: Eaton Страницы: 27

Бренд: macromatic Страницы: 2

Бренд: CTI Страницы: 30

Бренд: BPC Страницы: 8

Бренд: F&F Страницы: 4

Бренд: Viessmann Страницы: 4

Бренд: Theben Страницы: 7

Бренд: TECO Страницы: 66

Relion 615 series

Бренд: ABB Страницы: 40

Бренд: Thytronic Страницы: 28

Бренд: Keysight Страницы: 132

Бренд: Pilz Страницы: 8

Бренд: Pilz Страницы: 16

Бренд: Pilz Страницы: 6

Бренд: Pilz Страницы: 23

Guardmaster MINOTAUR MSR121RT

Бренд: Allen-Bradley Страницы: 4

Бренд: macromatic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды