Basler BE1-BPR страница 139 Скачать руководство пользователя

Страница: 139 / 148

BE1-BPR Appendix

A-3

Step 3. Select Settings/Terminal Preferences.

a. Using Figure A-4 as a guide, make the

following selections in the dialog box:

Check the

Line Wrap and Local Echo

boxes to enable these functions.

Disable the

CR->CR/LF Inbound

function.

Enable the

CR->CR/LF Outbound

function.

b. Set the

Buffer Lines at 244.

c. Click “OK”.

Step 4. Select Settings/Text Transfers

a. Make the following selections

using Figure A-5 as a guide.

Set Flow Control at

Line at a

Time.

Enable

Delay Between Lines and set the

delay at 1 or 2/10 Sec.

Disable

Word Wrap...

b. Click “OK”.

Step 5. Select Settings/Communications

a. Make the following selections:

Under

Connector, select the appropriate

communiation port for your computer.

Adjust the Baud Rate setting so that it
matches the setting of the relay. The
default baud rate of the BE1-BPR is
9600.

rate of the relay is 9600.

Set the Data Bits at

Disable

Parity Check.

Set the Stop Bits

at 1.

Set Flow Control

to Xon/Xoff.

b. Click “OK”.

Step 6. Click File/Save. Enter a desired file name, e.g., BE1-BPR.trm. For future communication

sessions, click File and open this file. Terminal will automatically be set up properly to
communicate with the BE1-BPR relay.

Step 7. Terminal is now ready to communicate with the relay. Table A-1 describes the required

connection for each RS-232 port.

Figure A-4. Terminal Preferences Dialog Box

Figure A-5. Text Transfers Dialog Box

Figure A-6. Communications Dialog Box

Содержание BE1-BPR





















































































































































Результаты поиска

Содержание BE1-BPR

Отзывы:

Похожие инструкции для BE1-BPR

Бренды по названию

Популярные бренды

Basler BE1-BPR, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-BPR

Отзывы:

Похожие инструкции для BE1-BPR

Бренды по названию

Популярные бренды