Basler BE1-BPR Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 148

background image

BE1-BPR Functional Description

4-9

Changing Parameters Using Communication Ports

Changing settings through a communication port requires an ACCESS-CHANGE-SAVE-CONFIRM cycle.
The operator uses the ACCESS command to obtain a program (change) access level. Different passwords
give access to change different parameters.

ACCESS

Programming changes access

HMI Menu Branch: N/A

Comments

This command is used to gain access to an access area before making programming or
settings changes. The access areas available are:
ACCESS AREA 1: Access is provided by password 1 (PW1). PW1 allows write access to

all setting and operating registers with no restrictions.

ACCESS AREA 2: Access is provided by password 2 (PW2). PW2 permits changes to be

made to relay protection settings.

ACCESS AREA 3: Access is provided by password 3 (PW3). PW3 allows breaker related

settings changes to be made.

ACCESS AREA 4: Access is provided by password 4 (PW4). PW4 allows control or relay

outputs for testing purposes.

Access to an area is granted when the appropriate password is entered. If password
protection is disabled in one or more areas, then no password is required to gain access to
the unprotected levels. If a valid password is entered, the relay responds with the access
area provided by that password. If an invalid password is entered, an error message is
returned.

ACCESS Command
Purpose:

Reads or changes access area so that programming or settings changes can be made.

Syntax:

ACCESS[=<password>]

ACCESS Command Examples

1.

Obtain area two access.

ACCESS=OPENUP

ACCESS GRANTED
AREA 2

2.

Read the current programming access area.

ACCESS

AREA 2

After the change(s) are made, the new data must be saved using the SAVE command. The operator must
confirm that the programming is completed before the changes are actually made. If no password protection
is used, it is still necessary to obtain programming/change access in order to protect against accidental
changes. If password protection is disabled then ACCESS=BPR or any other string will be accepted in place
of a password.

SAVE

Exit programming mode and save changes

HMI Menu Branch: N/A

Comments

This command is used at the end of a programming or settings changing session to save
the changes made. When the SAVE command is entered, the relay responds with a
confirmation message (ARE YOU SURE (Y/N)?). If Y is entered, programming or settings
changes are saved to non-volatile memory, the programming mode is exited, and the relay
is returned to an on-line condition. Entering N exits the programming mode without saving
changes and returns the relay to an on-line condition.

«
...
50
51
52
53
54
...
»

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

Бренд: M-system Страницы: 4

Бренд: VERIS INDUSTRIES, INC. Страницы: 2

System pro M RHI

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 52

Бренд: ABB Страницы: 22

Бренд: ABB Страницы: 68

Бренд: ABB Страницы: 7

Бренд: ABB Страницы: 72

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 3

Бренд: ABB Страницы: 100

Бренд: ABB Страницы: 60

Бренд: ABB Страницы: 38

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 72

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 64

Бренд: ABB Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды