Basler BE1-BPR страница 56 Скачать руководство пользователя | Manualshive

Страница: 56 / 148

background image

BE1-BPR Functional Description

4-13

(17(5 3$66:25'

Password Protection Example

If the following password protection is desired:

Area One changes to only be performed from the front panel by personnel with the
password OPENUP.

Area Two changes to be performed with no password required but only from the front panel.

Area Three changes to be performed from either the front or rear panels by personnel
with the password BKRGRP.

Area Four control to be accessed from the front panel by personnel with the password TEST.

The passwords are programmed as follows:

>ACCESS=BPR

>ACCESS GRANTED LEVEL 1

>PW1=OPENUP,F

Password for Area One

>PW2=0,F

Password for Area Two

>PW3=BKRGRP,B

Password for Area Three

>PW4=TEST,F

Password for Area Four

SAVE

ARE YOU SURE (Y/N) ?

Y

Relay verification. Enter Y to save the data.

RELAY OFF_LINE

CHANGES SAVED

The new passwords are now operational.

RELAY ON_LINE
>

The Programming A New Password sub-section provides another example of changing password protection.

Entering An Access Password At The Front Panel

To change settings from the front panel, first enter the PROGRAM mode by pressing the PROG key. The
password prompt appears as shown below:

In the password prompt, "********" represents the password and the cursor is under the first (leftmost)
character. To enter a password, press the +/- key until the correct character is displayed. Press the right
arrow key to move to the next password character and press the +/- key until the correct character is
displayed.  Continue to enter password characters until the correct password is entered. If the password
is less than eight characters, use the down arrow key to end the entry.  After the eighth character is entered,
the password entry screen is automatically ended.  One of three possible screens appears for two seconds
before the original menu screen reappears. The three screen possibilities are:

If password is accepted

If the password is rejected

If programming conflict

$&&(66 *5$17('

/(9(/ B

$&&(66 '(1,('

$&&(66 '(1,('

$&&(66 &21)/,&7

or

or

The conflict screen will appear if program mode has already been entered through one of the rear serial
ports. The relay only allows programming to occur from one source at a time.

Entering An Access Password Through Communication Ports

When entering a password through communication ports, you must enter the password using the ACCESS
command (Example ACCESS=OPENUP). Passwords entered through a terminal keyboard are not case
sensitive. If a valid password is entered, an ACCESS GRANTED LEVEL x message is displayed. If an
invalid password is entered, an ACCESS DENIED message is displayed.

Target Data
The menu screen most often viewed is the TARGETS screen. Because of that, the TARGETS screen is the
default screen. Viewing order or progression through the menu screens is based on the expected frequency
of use.

«
...
54
55
56
57
58
...
»

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

ESR5-BWS-31-24VDC

Бренд: Eaton Страницы: 50

Бренд: ABB Страницы: 18

Бренд: Davin Страницы: 12

TimeSaver Base Series

Бренд: Orbis Страницы: 2

Бренд: Yokis Страницы: 12

Бренд: Bamo Страницы: 4

Бренд: GE Страницы: 20

Бренд: GE Страницы: 24

Бренд: Thytronic Страницы: 146

Бренд: Vemer Страницы: 52

Бренд: Siemens Страницы: 7

Бренд: GE Страницы: 592

Бренд: WEG Страницы: 2

Бренд: KUSSMAUL Страницы: 1

Бренд: KUSSMAUL Страницы: 5

Бренд: Eltako Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды