manualshive.com logo in svg

Basler BE1-BPR, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-BPR - это необходимое руководство для правильной установки и использования данного продукта. Вы можете скачать этот мануал бесплатно на нашем сайте manualshive.com. Получите подробные инструкции по настройке и эксплуатации Basler BE1-BPR, чтобы обеспечить эффективное его использование.

Поделиться
Скачать
background image

BE1-BPR Installation

7-1

SECTION 7 • INSTALLATION

GENERAL

When not shipped as part of a control or switchgear panel, BE1-BPR Breaker Protection Relays (BPR) are
shipped in sturdy cartons to prevent damage during transit.  Upon receipt, check the part number against the
requisition and packing list to see that they agree.  Visually inspect it for damage that may have occurred
during shipment.  If there is evidence of damage, immediately file a claim with the carrier and notify the
Regional Sales Office, or contact the Sales Representative at Basler Electric, Highland, Illinois.

In the event the unit is not to be installed immediately, store it in its original shipping carton in a moisture and
dust free environment.  It is strongly recommended that an operational test (described in  Section 8) always
be performed prior to installation.

OPERATING PRECAUTIONS

Before installation or operation, note the following precautions.

1.

Always be sure that external operating (monitored) conditions are stable before removing a BE1-BPR
unit for inspection, testing, or servicing.  

2.

BE1-BPR relays are solid-state devices and have been type tested in accordance with the
requirements defined below under 

Dielectric Test.  If a wiring insulation test is required on the

switchgear or panel assembly of which this unit is a part, see 

Dielectric Test below.

3.

Be sure that the BE1-BPR case is hard wired to earth ground using the ground terminal on the rear
of the unit. 

4.

When the unit is in service, the controls should be protected by the plastic cover supplied.  This limits
access to the control settings.

Dielectric Test

All output and power supply terminals have MOV suppressors.  Maximum applied voltage must be no greater
than 300 volts where MOV suppressors are used.  Surge suppression capacitors are installed between
terminal pairs and between terminals and chassis ground.  When testing with 1,500 Vac, leakage current
(approximately eight milliamperes per terminal) is expected.  1,500 Vac (RMS) at 45 to 65 hertz or 2,121 Vdc
for one minute may be applied between circuit groups, and between circuit groups and chassis ground in
accordance with IEC 255-5 and ANSI/IEEE C37.90-1989 (Dielectric Tests).

MOUNTING

General

BE1-BPR relays are designed to be mounted in either 19 inch racks or conventional panels.  Overall
dimensions for the rack unit are shown in Figure 7-1.  The rack unit may be panel mounted at any convenient
angle, using the cutout dimensions of Figure 7-2 as a guide.  Figures 7-3 and 7-4 show the dimensions for
the vertical panel mount.  The cutout dimensions for the vertical panel mount are shown in Figure 7-5.  When
panel mounting the rack unit, an optional escutcheon plate can be installed to cover variations in panel
cutouts.  Figure 7-6 shows the mounting flanges removed and the escutcheon plate installed.  Figure 7-7
shows the mounting flange and alternate location that requires less mounting depth.

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

GE ML Series 350 Instruction Manual preview
ML Series 350
Бренд: GE Страницы: 280
Zander Aachen SR7C User Information preview
SR7C
Бренд: Zander Aachen Страницы: 4
ZiFiSense MTZT-IN01 Manual preview
MTZT-IN01
Бренд: ZiFiSense Страницы: 15
Danfoss VLT VLA 31 Instruction preview
VLT VLA 31
Бренд: Danfoss Страницы: 4
Microsafe Mkomfy 2G R-T 25A Installation Instructions User Instructions preview
Mkomfy 2G R-T 25A
Бренд: Microsafe Страницы: 12
ABB AS400 User Manual preview
AS400
Бренд: ABB Страницы: 14
Eaton E Series Cheat Sheet preview
E Series
Бренд: Eaton Страницы: 4
Contrel ELR-4 Instruction Manual preview
ELR-4
Бренд: Contrel Страницы: 4
Federal Signal Corporation 300TAR Instruction Sheet preview
300TAR
Бренд: Federal Signal Corporation Страницы: 20
Chromalox CS3 Installation Instructions Manual preview
CS3
Бренд: Chromalox Страницы: 8
Datakom DPR-145 User Manual preview
DPR-145
Бренд: Datakom Страницы: 19
GE CEY52B Instructions Manual preview
CEY52B
Бренд: GE Страницы: 36
GE IAV53K Instructions preview
IAV53K
Бренд: GE Страницы: 4
Siemens AG8 101-103 Manual preview
AG8 101-103
Бренд: Siemens Страницы: 100
Siemens SIRIUS 3RA2811 Original Operating Instructions preview
SIRIUS 3RA2811
Бренд: Siemens Страницы: 4
F&F BIS-412-LED Manual preview
BIS-412-LED
Бренд: F&F Страницы: 7
ADTRAN T1-FT1 CSU Specification Sheet preview
T1-FT1 CSU
Бренд: ADTRAN Страницы: 2
Valcom V-9955 Specification Sheet preview
V-9955
Бренд: Valcom Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды