Basler BE1-BPR Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 148

background image

BE1-BPR Application

2-19

Breaker Failure Logic 1 For Enhanced Relays (BFL1E)

BFL1E logic provides the following application features:

1.

Three-Pole Tripping BF Logic (No input or output latch-in provided). Three BFI inputs are available at
IN3, IN4, and IN5 to start delay timer T1. If the BFI inputs are not reset by the time timer 1 times out and
either the phase fault detector (F1) or neutral fault detector (F2) is picked up, then BFO1 (OUT1) closes,
tripping the backup breakers. Refer to the breaker failure timing diagram in Section 1 for information on
setting the delay and control timers.

2.

No Current BF Logic (No input or output latch-in provided). Some faults may not provide current to the
CTs (i.e. internal transformer failures). In this case, a BFI input is available (IN6) to start delay timer T2.
This input is not supervised by a fault detector. If the BFI input is not reset by the time the timer times
out, BFO2 (OUT2) closes, tripping the backup breakers. Refer to the breaker failure timing diagram in
Section 1 for information on setting the delay and control timers.

3.

Trip Coil Status Monitor. Preprogrammed logic is provided using IN1 to provide breaker status and IN2
for trip coil continuity. Refer to

Application Data in this section for further details on the circuit operation.

4.

Breaker Arc Protection. Preprogrammed logic is provided using fault detector 3 (F3) for the MAF fault
detector, IN1 for breaker status and OUT4 for the arc detector output. Refer to

Application Data in this

section for further details on the circuit operation.

5.

Block Reclose Output. Preprogrammed logic is provided using breaker resistor protection output (O13)
to drive the block reclose (BR) output (OUT3). Refer to

Application Data in this section for further details

on the circuit operation.

«
...
31
32
33
34
35
...
»

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

Бренд: ADTRAN Страницы: 20

Бренд: ADTRAN Страницы: 106

Бренд: Schrack Страницы: 4

Бренд: Elko Страницы: 3

Бренд: Elko Страницы: 3

Бренд: QUBINO Страницы: 9

Бренд: PIFace Страницы: 9

Бренд: QUBINO Страницы: 69

Бренд: Datakom Страницы: 19

ESR5-NO-41-24VAC-DC

Бренд: Eaton Страницы: 30

Бренд: National Instruments Страницы: 65

Бренд: ADTRAN Страницы: 2

Бренд: System Sensor Страницы: 4

KFD2-RSH-1.2E.L2

Бренд: Pepperl+Fuchs Страницы: 24

KFD2-RSH-1.2D.FL2

Бренд: Pepperl+Fuchs Страницы: 24

2 Channel USB Relay Module

Бренд: Numato Страницы: 19

Бренд: Climax Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды