Basler BE1-BPR страница 133 Скачать руководство пользователя | Manualshive

Страница: 133 / 148

background image

BE1-BPR Calibration And Testing

8-3

Note

Steps 3 through 16 of this procedure can be automated by using any word processor to
type all the required commands into an ASCII file. This file would then be downloaded to
the relay using any standard communications software package or by printing the file to
the serial port. This procedure requires that the communications program or the computer
serial port communication mode supports handshaking (flow control).

CHANGES SAVED

RELAY ON-LINE
>

B. Define custom logic by changing a preprogrammed scheme with the following commands:

>ACCESS=<password> or ACCESS=BPR if password not used.
> LN=<name of preprogrammed scheme to modify> (copies preprogrammed

scheme to custom logic memory)

> LN=<name of new scheme> (allows scheme to be changed)

Use LO, LF, LC, LT commands as required to change logic.

>LOGIC=<name of new scheme>
>SAVE

ARE YOU SURE (Y/N)?

- Y

RELAY OFF-LINE

CHANGES

SAVED

RELAY

ON-LINE

>

C. Define a custom logic scheme without copying any previous file.

>ACCESS=<password> or ACCESS=BPR if password not used.
> LN=<name of new scheme> (allows scheme to be changed)

Use LO, LF, LC, LT commands as required to change logic.
Disable the outputs or function modules not needed by setting them equal to 0.
(I.E. LO12=0)
All equations in a group can be programmed or disabled at once by not using a number.
Example 1: LC=2,12 changes all input logic to 2,12.
Example 2: LO=0 clears all output equations before writing new ones.

>LOGIC=<name of new scheme>
>SAVE

ARE YOU SURE (Y/N)?

- Y

RELAY OFF-LINE

CHANGES SAVED
RELAY ON-LINE
>

Entering Settings

Step 1.

Perform the preliminary setup procedure and select the operational logic.

Step 2.

Calibrate the A/D section of the relay using the A/D calibration procedure described above.

Step 3.

Enter program mode from the communication port by entering :

>ACCESS=<password> or ACCESS=BPR if password not used.

Step 4.

Enter the CT ratios, using the CT command.

Step 5.

Enter the PickUp settings, using the PU command.

Step 6.

Enter the Time Delay settings, using the TD and TD79 commands.

Step 7.

Program the format of the real-time-clock by using the PCLK command.

«
...
131
132
133
134
135
...
»

Содержание BE1-BPR





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-BPR

Бренд: ECTIVE Страницы: 12

Бренд: ERL Страницы: 24

Бренд: Schweitzer Engineering Laboratories Страницы: 614

Бренд: Philio Страницы: 5

Бренд: ABB Страницы: 152

Бренд: TE Connectivity Страницы: 2

Бренд: GE Страницы: 60

Бренд: GE Страницы: 28

Бренд: GE Страницы: 8

Бренд: ABB Страницы: 20

Бренд: Field Controls Страницы: 2

Pro Latch R 160

Бренд: Sterling Power Products Страницы: 21

Бренд: F&F Страницы: 6

Бренд: WEG Страницы: 148

Бренд: LOXONE Страницы: 2

Бренд: Jung Страницы: 13

Бренд: Jung Страницы: 22

Бренд: Climax Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды