AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 20 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

Rear View Diagram of PassFinder AP2520 VoIP Router (8-port VoIP Module)

ㅡ

AC110~220V

ETHERNET CONSOLE

SERIAL

(1) (2)

(3)

(4)

(6)

ACT

(7)

PHONE

SLOT 0

AP-FXS4

(5)

ACT

PHONE

SLOT 0

AP-FXO4

[ Diagram 1-4 PassFinder AP2520 VoIP Router / 8-ports Voice Module Rear Side ]

No.

Label

Description

(1)

LAN Port

Port for connecting UTP Type 10/100BaseTx Ethernet.

(2)

Console Port

With the provided console cable, connect with the
PC for equipment configuration. Mandatory for initial
setting.

(3)

WAN(SERIAL)

Port for 1 WAN(SERIAL) for router model.
Port for 1 LAN for gateway model.

(4)

Network

Module Slot 0

4 RJ11 Type Voice Ports. (FXS)

Status LEDs Provided

(5)

Network

Module Slot 1

4 RJ11 Type Voice Ports. (FXO)

Status LEDs Provided

(6)

Power Input

Plug

Connects power cable. The AP2520 VoIP router uses
both 110 and 220V AC.

(7)

Power Switch

Switch for power supply.

[ Table 1-2 PassFinder AP2520 VoIP Router / 8-port Voice Module Rear Side Description ]

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды