AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 260 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

260

5.7.3.16.5.

Examples

The following example configures the wink-signal duration on a voice port for
300 milliseconds:
voice-port 1/0

timing wink-duration 300

5.7.3.17.

timing wink-wait (E&M Voice Port Command)

To specify the maximum wink-wait duration for a specified voice port, use the

timing wink-wait

command in voice-port configuration mode. To reset the

default value, use the

form of this command.

timing wink-wait

milliseconds

no timing

wink-wait

5.7.3.17.1.

Syntax Description

Keyword / Argument

Description

milliseconds

Maximum wink-wait duration, in milliseconds, for a

wink start signal. Valid entries are from 100

to 5000

milliseconds. Supported on E&M ports only.

5.7.3.17.2.

Default

200 milliseconds

5.7.3.17.3.

Command Modes

Voice-port configuration

5.7.3.18.

Usage Guideline

The call signal direction for the

timing wink-wait

command is out

5.7.3.18.1.

Examples

The following example configures the wink-wait duration on a voice port for 300
milliseconds:

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды