AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 71 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

[Procedure]

Step

Operation

Enter into the interface configuration mode.

Give PPP encapsulation protocol to the interface.

Move to the IP configuration mode.

Give an IP address to the interface.

Enable CHAP or PAP authentication. (Optional)

Set CHAP or PAP parameters. (Optional)

Set PPP default peer IP. (Optional)

(If necessary) use “debug” command to check if the router is normally

operating.

(For the DCE configuration) set the clock rate.

Make the interface up.

With “show interface” command, check if the interface is normally

operating.

(For abnormal operation) find faults and recover faults as using “debug”

command.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды