AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 227 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

227

configuration mode.

5.7.2.4.5.

Examples

The following example accesses dial-peer configuration mode and configures

a POTS peer identified as dial peer 10:

configure

dial-peer voice 10 pots

5.7.2.5.

gateway

To enable the H.323 Voice over IP gateway, use the

gateway

command in

global configuration mode. Use the

form of this command to unregister this

gateway with the gatekeeper.

gateway

no gateway

5.7.2.5.1.

Syntax

This command has no keywords or arguments.

5.7.2.5.2.

Default Value

The gateway is unregistered.

5.7.2.5.3.

Command Mode

Global Configuration Mode

5.7.2.5.4.

Usage Guideline

Use the

gateway

command to enable H.323 VoIP gateway functionality. After

you enable the gateway, it will attempt to discover a gatekeeper by using the

H.323 RAS GRQ message. If you enter

no gateway

, the VoIP gateway will

unregister with the gatekeeper via the H.323 RAS URQ message.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды