AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 40 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

When booting the system, set Gateway environment and save configuration

information as using “copy running-config” command.

If the system is normally booted, the following message will appear.

System Boot Loader, Version 1.3.6/1

Copyright (c) by AddPac Technology Co., Ltd. Since 1999.

PassFinder Router Series (2520)

Serial Number: AP2520-ffff55

MPC855T 50MHz With 33554432 Bytes System Memory

524288 Bytes System Flash Memory

4194304 Bytes 2nd System Flash Memory

DS1742 Timekeeping RAM

1 RS232 Serial Console Interface

1 Ethernet/IEEE 802.3 Interface

1 Serial Networks Interface

2520 System software Revision 1.0

Released at Jun 5 14:25:32 2001

Program is 3012088 bytes, checksum is 0xd976800

Local Time : Mon Jul 9 11:07:14 2001

Copyright (c) by AddPac Technology Co., Ltd. Since 1999.

The system is not configured yet or backup data is invalid.

Please login to system as a "root" and make configuration.

Voice Module (0): FXO

Voice Module (1): FXS

DSP S/W download

Voice Module (0): .... OK

Voice Module (1): .... OK

The System is ready. Please login to system.

login:

Caution

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды