AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 131 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

131

4.10.

Transparent Bridging Configuration

The PassFinder AP2520 Gateway supports transparent bridging for Ethernet and

serial ports. Also, to manage networks, the PassFinder AP2520 Gateway

supports Bridge MIB that is defined in RFC 1286.

The bridge functions that the PassFinder AP2520 Gateway supports are as

follows:

Complying with IEEE 802.1D standard

Segmenting transparent bridged network to the logical VLAN

The bridge function is supported not only through the Ethernet but also

through the serial network and the frame-relay network.

Supporting the spanning-tree algorithm that adopts IEEE-based Bridged

Protocol Data Unit (BPUD)

PassFinder AP2520 series Gateways only support one bridge-group. Therefore,

the concept of the bridge-group is not used.

[Procedure]

Step

Operation

Move to the configuration mode.

Set option values to use in the bridge.

Go to the interface configuration mode.

Apply the bridge-group that has been set to the corresponding

interface.

For multi-access interfaces including frame-relay, make a map.

Apply other bridging option parameters to use.

Use “show bridge” or “show span” commands to check if the bridge

has been correctly set and the spanning tree algorithm normally

operates.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды