AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 295 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

295

5.7.5.8.3.

Command Mode

Gateway Configuration Mode

5.7.5.8.4.

Usage Guideline

The VoIP gateway is registered in the gatekeeper that is the Registration

Admission and Status (RAS) server and receives the charging service. The

AP2520 VoIP Gateway can designate maximum ten gatekeepers in a gateway

using this command. To view the list of the gatekeepers, use “

show gateway

”

command. If more than one gateway is designated, gateways try to register

themselves in the gatekeeper using the GRQ message according to their

priorities. There is only one gatekeeper that can be registered at the same

time. When a gateway receives the re-registration failure message or does

not receive any message, the next gateway tries to register itself in the

gatekeeper.

Users can designate the gatekeeper using this command or using the Alternate

GK list included in the message that the currently registered gatekeeper sends.

For reader’s reference, official gatekeeper multicast IP address based on H.323

standard is 224.0.1.41 and the port is 1718.

5.7.5.8.5.

Examples

The following example sets up a unicast discovery to a gatekeeper:

gkip 192.7.5.1

In the following example, the gatekeeper has 224.0.1.41 IP address (a multicast

IP address) and port 1718, and its priority is 0.

gkip 224.0.1.41 1718 0

5.7.5.9.

h323-id

To configure the H.323 name of the gateway identifying this gateway to its

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды