AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 181 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

181

the VoIP peer. While the above method sets only one CODEC, creating a

CODEC class makes several CODEC lists and enables flexible negotiation with

the VoIP router.

Create CODEC classes as follows:

Step Command

Description

Router# configure

Enters into the configuration mode.

Router(config)# voice class codec

tag

Enters into the CODEC class
configuration mode.

The tag is an identifier of the

CODEC class.

Router(config-class)# codec preference

value

codec-type

Enters into the configuration mode.

Router(config-class)# codec preference

value

codec-type

Enters into the configuration mode.

Router(config-class)# exit

Terminates the CODEC class

configuration mode. (After
configuration is completed,

configuration becomes valid.)

Then, save CODEC classes created above in a certain VoIP peer by the

following method.

Step Command

Description

dial-peer voice

tag VoIP

Enters into the dial-peer setup mode to set the

VoIP peer.

voice-class

codec

codec-class-tag

Selects a CODEC for the voice considering the

voice coder rate.

The following example shows how to create CODEC class 99 and store it in the

VoIP peer 108.

voice class codec 99

codec preference 1 g7231r63

codec preference 2 g729

dial-peer voice 108 VoIP

voice-class codec 99

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды