AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 277 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

277

5.7.4.10.1.

Syntax

Keyword / Argument

Description

string

Integers representing the prefix of the telephone
number associated with the specified dial peer.

Valid numbers are 0 through 9, and a comma (,).

Use a comma to include a pause in the prefix.
(max length 55)

5.7.4.10.2.

Default Value

Null string.

5.7.4.10.3.

Command Mode

Dial-Peer Configuration Mode

5.7.4.10.4.

Usage Guideline

Use the

prefix

command to specify a prefix for a specific dial peer. When an

outgoing call is initiated to this dial peer, the

prefix

string

value is sent to the

telephony interface first, before the telephone number associated with the dial

peer.

If you want to configure different prefixes for dialed numbers on the same

interface, you need to configure different dial peers.

5.7.4.10.5.

Examples

The following example specifies a prefix of "9" and then a pause:

dial-peer voice 10 pots

prefix 9,

5.7.4.11.

register

To configure a gateway to register or deregister a fully qualified POTS dial-peer

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды