AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 157 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

157

4.14.2.

Password Recovery

The Gateway manager shall know the password to change Gateway

configuration and check the Gateway status. Therefore, the Gateway

manager shall remember the password and keep it confidentially. This

chapter describes how to recover the password when the Gateway manager

forgets the password.

The following describes how to recover the password.

[Procedure]

Step

Operation

Connect the console and prepare to recover the password.

Password recovery shall be made in the console only.

Initialize the system. (Turn on/off the system.)

After the initial messages are displayed, enter Ctrl+x and Ctrl+c once

or twice.

Wait for a while until entering into the boot mode.

Use “Show password” command to check the root password.

Reboot the system.

Initialize the system in the booter mode, not in the Gateway program state.

enter into the booter mode, enter Control-X and Control-C keys once or twice

when the booter mode message Appears.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды