AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 280 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

280

5.7.4.12.3.

Command Mode

Dial-Peer Configuration Mode

5.7.4.12.4.

Usage Guideline

Use the

session-target

command to specify a network-specific address or

domain name for a dial peer. Whether you select a network-specific address or

a domain name depends on the session protocol you select.

5.7.4.12.5.

Examples

The following example configures a session-target IP address "211.238.1.1".

dial-peer voice 10 VoIP

session-target 211.238.1.1

5.7.4.13.

shutdown (Dial-Peer)

To change the administrative state of the selected dial peer from up to down,

use the

shutdown

dial-peer configuration command. Use the

form of this

command to change the administrative state of this dial peer from down to

up.

shutdown

5.7.4.13.1.

Syntax

This command has no arguments or keywords.

5.7.4.13.2.

Default Value

No shutdown

5.7.4.13.3.

Command Mode

Dial-Peer Configuration Mode

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды